What is considered the strike side of a door?
The strike side of the door is opposite the hinged side. You will find the strike plates on the door jamb aligned to the door knob and deadbolt. These are where the latch and bolt sit to ensure that your door stays closed and enhance its security for your protection.
What is a strike on a door frame?
When discussing door hardware, a “strike” or “door strike,” refers to the metal plate or assembly that’s installed into or onto a door frame to “catch” the latch or bolt to hold the door closed.
What is the hole on the side of a door called?
The latch bore, also known as the edge bore, is the hole drilled from the side of the door into the cross bore to allow the latch of the lock to be installed and to accommodate the sliding of the deadbolt. The diameter of the latch bore is generally 1” to accommodate bolts from either mechanical or electronic locksets.
Do doors need a strike plate?
Strike Plate This is the plate the latch-tongue, or deadbolt-tongue will connect with. It should sit flush with the door jamb. Any passage or privacy set needs to have a strike plate for the door to latch. Additionally, deadbolts need a strike plate to properly lock.
What are the parts of a door frame?
A Quick Guide: Parts of a Door
- Door frame. The door frame is the entire framework supporting the door, including the sill, jamb and head.
- Sill. The door sill is the very bottom part of the door frame that rests on the floor.
- Jamb/door jam.
- Head.
- Panel.
- Astragal.
- Fixed panel.
- Door sweep.
Why do you need a strike plate on a door?
The strike plate attaches to and protects the door jamb. This is the plate the latch-tongue, or deadbolt-tongue will connect with. It should sit flush with the door jamb. Any passage or privacy set needs to have a strike plate for the door to latch.
What is the metal part on the door frame called?
strike plate
A strike plate is the metal piece attached to the door jamb. As the door closes, the latch mechanism strikes the plate mounted to the jamb and the strike plate catches the mechanism and holds the door closed.
What is a door sash?
A sash is a moveable piece of glass that is used in a window or door. Several sashes are typically joined together to make a frame of glass panels.
What does a door strike plate look like?
Latches are typically spring-loaded, and they lock into place when the door is fully closed, keeping the door secure. The third part is the door strike (also called the “strike plate”), which essentially looks like a metal plate with a hole (or holes) cut out of it.
What is a door strike on a lock?
The third part is the door strike (also called the “strike plate”), which essentially looks like a metal plate with a hole (or holes) cut out of it. The door strike is fastened, usually by screws, onto the frame of a doorway, and it is carefully aligned with the lockset in order to give the latch a place to sink into when the door closes.
What is a strike plunger on a door?
The strike plunger enters a strike plate on the jamb and keeps the door closed, locked or both. The force of a door closing hard repeatedly, or being forced open, can damage the door frame at the area of the strike plate. When this happens, it’s necessary to fix the frame before it gets worse and needs replacement.
How do you Shim a door with a strike plate?
Install a wood shim in the gap behind the jamb at the area of the strike plate. Tap the end with a hammer to create a 1/8-inch gap between the face of the jamb and the edge of the door. Secure the shim in place with a 6d finish nail through the face of the jamb above and below the area of the strike plate.
What is the top part of a door frame called?
The top horizontal section of a door or window frame is called the head jamb. These are the vertical components on each side of a door or window frame. Side jambs are the part of the door that gets fastened to the framing with screws or nails.
https://www.youtube.com/watch?v=AUL-R_E46fw